Skip to main content

A Simple DIY Walking Robot

In this simple project, I will show you how to make a DIY Walking Robot with very minimum components. This Walking Robot doesn’t require Arduino or Raspberry Pi. All you need is a 5V geared motor, a battery and a few popsicle sticks.

Introduction

Over the period in Electronics Hub, I have implemented a variety of robots like Hand Gesture Controlled Robot, Obstacle Avoiding Robot, Line Follower Robot, Robotic Arm, Remote Controlled Robot, etc.

All these robots have few things in common like a Microcontroller (Arduino UNO in most cases), a Motor Driver (L293D or L298N), couple of motors, chassis etc. But the robot I am about to build doesn’t require all the fancy electronics or programming.

Idea behind DIY Walking Robot

The idea behind this DIY Walking Robot is that you don’t need costly robot chassis or the above-mentioned electronics to build a working robot. A simple mechanical structure with a small rotating part (like a motor) is sufficient to successfully build a robot.

Without further delay, I will jump to a step-by-step explanation of building this DIY Working Robot.

Constructing the Walking Robot

Motor and Battery

The important part of this robot is the motor. I have used a 5V 150 rpm geared motor. To power this, I have used a small Li-po battery. You can use a switch in series with the battery and the motor but I have connected them directly.

Make sure that the motor has a dual sided shaft, the small white plastic piece where you usually connect a wheel.

Simple DIY Walking Robot Motor and Battery

Also, I have fixed the battery on the back of the plastic casing of the motor so that it stays firm without wobbling.

Getting the Popsicle Sticks Ready

The next step is to take a bunch of ice cream sticks (popsicle sticks) and cut them into the following specified shapes and sizes.

Simple DIY Walking Robot Popsicle Sticks Dimensions

These numbers are just based on trial and error and you do not have to follow the exact specifications. Pierce holes at the center of both the 11cm sticks. Also, pierce holes on the 1.7cm sticks, not at the center but slightly off.

Connecting Sticks to Motor

Now, take the two 1.7cm sticks and connect them as shown below so that the pierced holes stay on the opposite ends. This is important to simulate the walking effect.

Simple DIY Walking Robot Motor with Sticks

Now take the 6.5cm stick and fix two rubber tubes as shown in the image. The legs pass through these rubber sleeves. Fix the 6.5cm stick to the motor as shown in the image.

Simple DIY Walking Robot Motor Rubber Sleeve

Building the Legs

The next important step is to build the legs of the Walking Robot. Take the two 5cm sticks and fix the 7.5cm stick as shown below. This structure acts as the base of the leg.

Simple DIY Walking Robot Base of Leg

Now, for the actual leg part of the robot, take the 11cm long stick and fix it to the center of the base structure i.e. center of the 7.5cm stick.

Simple DIY Walking Robot One Leg

This whole structure makes one leg of the robot. Now, make an identical structure as the other leg using the similar sticks. This section completes the leg part of the robot.

Simple DIY Walking Robot Two Legs

Attaching the Legs to Motor

Now take one leg structure and try to fix it to the motor. First, slide the open end of the leg into the rubber sleeve and at the center, where the earlier pierced holes meet, place a thumb pin or something similar to hold the leg onto the motor.

The thumb pin also allows the leg structure to freely move at the pivot point.

Simple DIY Walking Robot One Leg to Motor

Now take the other leg structure and place it on the other side of the motor. The final structure looks something like this.

Simple DIY Walking Robot Final Structure

Make the Robot Walk

After confirming all the joints are glued properly, you can start the motor to test the Robot. In case you used a switch, turn on the switch and the motor start rotating. Due to the mechanical structure of the robot, the rotation of the motor’s shaft, transforms into a to and fro motion of the legs of the robot.

Since the legs are placed at a different angle, when one leg is forward, the other leg is at the back and the rotating motor will cause them to change positions alternatively, and a walking motion is simulated.  

Conclusion

A simple DIY Walking Robot without Arduino or motor driver is designed and constructed in this project. This can be a fun project for kids to get interested in robots and as it doesn’t involve any electronics and programming, they can easily build one.

The post A Simple DIY Walking Robot appeared first on Electronics Hub.



from Electronics Hub http://bit.ly/2H1DNhZ

Comments

Popular posts from this blog

TE Connectivity Announced Ultra Small Spring Fingers

TE Connectivity (TE)’snew ultra small spring fingers have one of the smallest footprints in the market to save valuable PCB space, allowing for use in a broad range of applications with space constraints across various industries.TE’s ultra small spring fingerscan save valuable PCB space with one of the smallest footprints in the market. Closed-loop contact design ensures reliable connection to the PCB, better normal force and higher current capacity (1.5A). Robust side wall minimizes over- compression. Special anti-lifting design can improve assembly e ciency by locking the tip of the contact within the sidewall of the spring  nger, which helps prevent the contact from getting caught on an operator’s glove during assembly. Pick-and-place area supports auto-assembly processes. It also offered in different heights and styles.As an authorized distributor for TE Connectivity, Heilind Asia provides TE’s products and also value added services. Heilind Asia supports both original equipment …

Hanwha TechwinCollects Two NPI Awards for Its Cutting-Edge Modular Mounter and Screen Printer at APEX

Hanwha Techwin Automation Americas, formerly Samsung C&T Automation, today announced that it has received two 2019 NPI Awards in the categories of Component Placement – High-Speed for its HM520 Cutting-Edge Modular Mounter and Screen/Stencil Printing for the ESE US-2000XF. The awards were presented to the company during a Tuesday, Jan. 29, 2019 ceremony that took place at the San Diego Convention Center during the IPC APEX EXPO.With the HM520 Modular Mounter, actual productivity is highest among machines of the same class and is optimized to high quality production. The system configures a flexible production line by applying a modular head and various production modes. The HM520 realizes unmanned, non-stop, and zero-defect production using the Smart Factory S/W Solution.The high performance HM520 offers a compact foot print, auto-calibrating maintenance free feeders, and modular heads. The HS(High Speed) Head offers a 20 Spindle x 2 Gantry, 80,000 CPH, ±25 μm @ Cpk ≥ 1.0, 0201 ~ …

Siemens partners with TIES, a Chinese R&D Center to develop new technologies for electric vehicle batteries

Advanced Battery Technology Innovation Center (ABTIC) is initiated jointly by Tianmu Lake Institute of Advanced Energy Storage and Siemens to develop advanced battery technologies and help bring them to volume productionABTIC aims to develop and provide digital solutions for production chains and innovation chains on next generation batteriesSiemens Digital Industries Software has partnered with Tianmu Lake Institute of Advanced Energy Storage Technologies (TIES), a major Chinese energy storage research and development center, to build an Advanced Battery Technology Innovation Center. The Innovation Center, to be located at the 500 million-yuan, 51,000 square meter TIES facility in Liyang, China, will be dedicated to transforming and upgrading the advanced battery industry, including nurturing advanced battery technology research and development, and the development and introduction of high-end talents in this growing area.The Innovation Center will provide the advanced battery innova…