Skip to main content

A Disaster and a Half

Every autumn deserves its pumpkin hacking projects. This Halloween, our pumpkin comes with a horror story. It began last year in early November. All the Halloween decorations were on clearance, and I found a plastic jack-o-lantern bucket for 15 cents. On first sight, I knew I must remote control it. Over the months following, the project came to my work bench now and then. I did simple things like cutting holes for the wheels, and mounted some of the mechanical things. Cutting the plastic with a utility knife was super easy.

Around the end of September this year, I sifted through my scavenged collection of electronics and formulated a plan. I decided on some Bluetooth devices because I wanted to explore that technology. The particular board in my stockpile was discarded from the product development process (insert eerie sound effects here). I didn't know its history. I didn't know if it had the standard released bootloader. I didn't even know if it worked. I was driven to make this pumpkin roll, so I chose to go forward with it. Our SparkFun nRF52832 breakout board would provide the brains and radio for the operation. The new Qwiic Motor Driver would control the drivetrain. Last, a SparkFun USB LiPoly Charger would provide battery management for the whole system.

SparkFun nRF52832 Breakout

SparkFun nRF52832 Breakout

WRL-13990
$19.95
9
Qwiic Cable - 100mm

Qwiic Cable - 100mm

PRT-14427
$1.50
SparkFun Qwiic Motor Driver

SparkFun Qwiic Motor Driver

ROB-15451
$14.95
SparkFun USB LiPoly Charger - Single Cell

SparkFun USB LiPoly Charger - Single Cell

PRT-12711
$15.95
8
SparkFun Qwiic Adapter

SparkFun Qwiic Adapter

DEV-14495
$1.50
Dual Motor GearBox

Dual Motor GearBox

ROB-00319
$10.95
3
Toy Tires - Off Road

Toy Tires - Off Road

ROB-00422
Retired

Confident in my success, I walked over to marketing and asked to write a blog about this project ( tense orchestra music), and we set the blog date near Halloween. It was only some wiring and software development – what could go wrong?

Drama and jokes aside, I’m bummed I don’t have a pumpkin to show today. My job here is IT, not EE, so this is my free time hobby. I have a number of other things that consume that free time, such as my two young children. Here are the high-level things that went wrong with the pumpkin.

IDE

PlatformIO

My first holdup was getting any code to upload to the Nordic board. I recently started using PlatformIO and it’s awesome. It has the features of Visual Studio Code (or Atom) and a huge number of board and library definitions built in. The SparkFun nRF52832 breakout board is not explicitly in the list of supported boards. If I understand this GitHub issue, a breakout board is close enough to a bare chip to not merit its own named board definition.

That hindered my progress in my first-choice IDE. I’m certain I could get it to work with enough time, but I was already so close to my deadline so I chose to try something else.

Segger Embedded Studio

My second choice was to follow Nordic Semiconductor’s recommendation: Segger Embedded Studio with the Nordic SDK. SES is focused on ARM chipsets, and has a workflow that resembles Visual Studio. Nordic has built their SDK to integrate into SES. This combo provides the best capability for working with Nordic SOCs on OS X. I spent a couple hours following the instructions, trying to troubleshoot why SES didn’t find the SDK. I’ve set up IDEs with SDKs before, and I know issues such as this can take a huge amount of time to fix. I stopped there. The IDE looks like it’s great for ARM development, so I look forward to getting back in there another time.

Arduino

I fell back on the old familiar. SparkFun has a board definition for our nRF52832 breakout board in Arduino, so that situation got me out of my standstill. On to software development!

Bluetooth

Bluetooth is a large topic; I didn’t know quite how large until I dove in. The process of developing firmware would take longer than expected. A Bluetooth network must have a central node and the rest are peripheral nodes. Each node specifies what it can do in one or more profiles. A profile can have multiple services. Each service can have multiple characteristics. A characteristic has a value (usually shown in hex) with one or more permissions assigned to it. Each of those pieces has a UUID associated to keep them all straight. There are standard profiles with reserved UUIDs for things like mouse, keyboard and audio devices.

The task of inventing the Pumpkin Control Profile didn’t pan out as I hoped. I also tried to find a profile to use with a ready-made phone app (more on that below). I resorted to a UART profile I found in the examples of the BLEPeripheral library.

The BLEPeripheral library does a great job making some of all that complexity more accessible. It even forced me to learn how to spell peripheral. However, it does not enable the user to create a central node. I’m bound to using a phone or computer to act as my central node until I can determine how to get center functionality in an ARM chip.

iOS Apps

I tried two iOS apps with joysticks for Bluetooth. Each of them required some specific hardware. I assume they’re looking for the UUIDs or device names of the product they support, and I tried to get information I needed to fake them out. Maybe the info is out there, or I’m overthinking it. Either way, the joystick on the phone didn’t happen. Nordic has some awesome mobile apps for their products. The nRF Toolbox app, among other functions, has a UART feature with assignable buttons. I gave each button a couple of ASCII characters that correspond to instructions for the two motors in the pumpkin firmware.

Hardware

Poorly planned connector placement

Disconnectable assemblies are my favorite. Whenever possible, my projects have pin headers and other connectors wherever the solder joints occur. This makes it possible to untangle the spaghetti.

The buttons for this board are smallish, and they are necessary to put the device in DFU mode. That is not a huge problem, but I chose to put all of the connections to the board on the same side as the buttons - not good. There is now a tiny fence around it, and my finger barely fits inside. Uploading to the pumpkin meant I had to find the button by touch and hold it while plugging in the FTDI cable. I spent most of my time developing on another of the same board with no such impediments.

I2C

The I2C didn’t seem to work for me at the start. After plenty of trial and error, I noticed a highly valuable comment from Bobby on our tutorial page. Basically, you have to define in Arduino the SDA and SCL pins you want to use. After a couple of hours, I thought I was finally ready, and no - the devices didn’t connect. I tested the motor driver with RedBoard and Qwiic shield, so I know it works. This is the final problem. I’d have a drivable pumpkin if I could get them to talk. It’s fixable, but not in time for this blog post.

alt text

Defeat vs Failure

If you’ve made it this far into the horror story, you’ve reached the unresolved ending. Will the pumpkin make it out alive? Will the gremlins kill it? It’s also the most important part of this story. I love a podcast called Making It. It’s three YouTubers that converse about making physical things for content on their channel. One of the recurring themes in the podcast is how to deal with not succeeding. When you make a thing, it may not turn out as expected. That’s the situation I’m in, so I get this following bit of inspiration from the podcast.

As of this writing, I’m defeated. The pumpkin doesn’t work, but to quote Thomas Eddison:

I have not failed, I have just found ten thousand ways that won’t make a remote control pumpkin.

If I stop now, I will fail. However, I’m going to get this pumpkin rolling. Since the problem is the I2C connection, I can either fix it or replace it with a simpler motor driver. I’m also keeping a positive attitude about all the external things I used in this project. I won’t blame the IDE or the manufacturers when it was clearly my preparation and decisions that led me here.

I may be defeated at the time of this post, but I won’t fail. Watch the comments for updates on this pumpkin. While you’re down there, misery loves company. I’d love to hear your horror stories too.

comments | comment feed



from SparkFun: Commerce Blog https://ift.tt/34fSWVG

Comments

Popular posts from this blog

TE Connectivity Announced Ultra Small Spring Fingers

TE Connectivity (TE)’snew ultra small spring fingers have one of the smallest footprints in the market to save valuable PCB space, allowing for use in a broad range of applications with space constraints across various industries.TE’s ultra small spring fingerscan save valuable PCB space with one of the smallest footprints in the market. Closed-loop contact design ensures reliable connection to the PCB, better normal force and higher current capacity (1.5A). Robust side wall minimizes over- compression. Special anti-lifting design can improve assembly e ciency by locking the tip of the contact within the sidewall of the spring  nger, which helps prevent the contact from getting caught on an operator’s glove during assembly. Pick-and-place area supports auto-assembly processes. It also offered in different heights and styles.As an authorized distributor for TE Connectivity, Heilind Asia provides TE’s products and also value added services. Heilind Asia supports both original equipment …

Hanwha TechwinCollects Two NPI Awards for Its Cutting-Edge Modular Mounter and Screen Printer at APEX

Hanwha Techwin Automation Americas, formerly Samsung C&T Automation, today announced that it has received two 2019 NPI Awards in the categories of Component Placement – High-Speed for its HM520 Cutting-Edge Modular Mounter and Screen/Stencil Printing for the ESE US-2000XF. The awards were presented to the company during a Tuesday, Jan. 29, 2019 ceremony that took place at the San Diego Convention Center during the IPC APEX EXPO.With the HM520 Modular Mounter, actual productivity is highest among machines of the same class and is optimized to high quality production. The system configures a flexible production line by applying a modular head and various production modes. The HM520 realizes unmanned, non-stop, and zero-defect production using the Smart Factory S/W Solution.The high performance HM520 offers a compact foot print, auto-calibrating maintenance free feeders, and modular heads. The HS(High Speed) Head offers a 20 Spindle x 2 Gantry, 80,000 CPH, ±25 μm @ Cpk ≥ 1.0, 0201 ~ …

Siemens partners with TIES, a Chinese R&D Center to develop new technologies for electric vehicle batteries

Advanced Battery Technology Innovation Center (ABTIC) is initiated jointly by Tianmu Lake Institute of Advanced Energy Storage and Siemens to develop advanced battery technologies and help bring them to volume productionABTIC aims to develop and provide digital solutions for production chains and innovation chains on next generation batteriesSiemens Digital Industries Software has partnered with Tianmu Lake Institute of Advanced Energy Storage Technologies (TIES), a major Chinese energy storage research and development center, to build an Advanced Battery Technology Innovation Center. The Innovation Center, to be located at the 500 million-yuan, 51,000 square meter TIES facility in Liyang, China, will be dedicated to transforming and upgrading the advanced battery industry, including nurturing advanced battery technology research and development, and the development and introduction of high-end talents in this growing area.The Innovation Center will provide the advanced battery innova…